6 In 1 Multi Functional 85mm Auto GPS Speedometer Tachometer Oil Pressure Water Temp Voltmeter

About This Product

- Put the gauge in the hole. -Measure and display current speed at a refresh rate of 0.25 seconds -IP67 waterproof and dustproof grade -12VDC Working Voltage -Fixing dimension: 85mm diameter (3-3/8), 70mm Depth (2-3/4”), GPS Sensor/Antenna wire is 12 feet long -Indicating Range: digital GPS Speedometer, digital Tachometer, Hour Meter, COG/ODO, Trip Meter, Water Temp, Fuel Level, Oil Pressure, Voltmeter -Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc. So i suggest tacho sensor signal. It is more stable. - For the GPS antenna, you should securely fasten it in the flat position, black side upwards, preferably outside (or inside front windscreen) so that it has a clear view of the sky to pick up satellite signal. Kenneth Houseknecht was 14 years old on April 19, 1988 when he broke into a Deptford home looking to steal $50 so he could buy porn magazines. There was just one problem: 12-year-old Kim Anderson... GPS Speedometer keeps counting ? - After installation in the first time, GPS speedometer needs to search for signal, that's the reason that LCD counts numbers all the time. Product Introduction How to install it ? 1. Cut an 85mm (3 3/8) hole in the panel and allow a clearance of 70mm (2 3/4”) behind the panel to fit the gauge. ELING ECP Multi-functional Gauge Meter (12V How to switch speed unit ? - Power on the power supply first. - Put the gauge in the hole and screw down. - Short press the back MODE button to show speed unit (Knots, MPH, Km/h). then adjust speed ratio from 1-300 according to your request. 3. After setting, Data is automatically saved. 4. Please note: If your sensor is installed on the flying wheel panel, the RPM ratio is equal to the number of gears of the engine; If the speed signal takes from W-Terminal, the RPM ratio is equal to the half of the number of poles. 5. Normally, When the engine is at idle state, tachometer shows 600-800rpm that means speed ratio is correct. - Using M4 nut and C type bracket to seal up the gauge. Logitech G29 6 In 1 Multi Functional 85mm Auto GPS Speedometer Tachometer Oil Pressure Water Temp Voltmeter Digital Speedometer Car Mph ohm signal refers to manual page 2. -Oil pressure meter, match pressure sensor. ELING 6 in 1 Multi-functional Gauge Meter GPS Speedometer Tachometer Hour Water Temp Fuel Level Oil Pressure Voltmeter 12V 85mm With Backlight : : AutomotiveEling Parts Ltd. specializes in marine and auto parts (e.g. gauges and sensors) over the decades. Our products are widely used in boats, yachts, cars, motorcycles, trucks, tractors, buses, generators, etc. Our factory, which is... And do not cut cable. Which gauges need to be used with sensors ? - Speedometer, match GPS antenna. -Tachometer, match tacho sensor. is B07WPXL7WQ or B07WPXFH34 Connect the antenna cable to socket in the back of the gauge. -Measure and display current speed at a refresh rate of 0.25 seconds -IP67 waterproof and dustproof grade -Stepper motors used for full range of stepping gauges, great feature with its less power consumption, longer life, higher precision, etc. - No Subscription is required, the GPS service is totally free. How to adjust backlight ? 1.Power on the power supply first. 2.Press the back SET button or Multi-function button (less than 2 seconds) to change the back light color. 3.Color in sequence: Red, Orange, Green, Yellow, Kelly, Blue, Purple, White，Auto Mode. 4. When users select the AUTO MODE, the back light will be off for around two seconds, and switch automatically as above sequence per minute. If not, you can turn down or turn up speed ratio to check RPM difference. If you need tacho sensor, pls. search for ASIN NO. No Subscription is required, GPS service is free, Antenna/Sensor is 12 feet long, cannot be cut. - After getting signal, LCD will come back to 0. It is normal. How to setting Tach RPM Ratio ? 1. Turn on the power supply first. 2. Press and hold the mode button for 3 seconds to enter the setting speed ratio mode. -Water temp meter, match temp sensor.